You can easily check the charge level by following these simple steps:
1. Press for 1 second the ON/OFF button;
2. The LEDs will turn on and indicate the level of charge:
- 1 LED = low charge level
- 4 LEDs = device is fully charged.
1. Press for 1 second the ON/OFF button;
2. The LEDs will turn on and indicate the level of charge:
- 1 LED = low charge level
- 4 LEDs = device is fully charged.
It takes approximately 90 minutes to fully charge the IQOS 2.4P Pocket Charger from an electrical outlet. Only charge IQOS 2.4P device using the supplied AC Power Adaptor and USB cable.
The IQOS device does not require a full charge to work. If the IQOS 2.4P Pocket Charger is fully charged you may use the holder for up to 20 times.
You can easily do a reset of your IQOS 2.4P device by simultaneously pressing and then releasing the Bluetooth and Power Buttons until all lights briefly blink.
Holder vibrations are activated in the following situations:
- At the start of heating (once you press the Holder Button to start);
- When the experience is nearly complete (30 seconds prior the end).
- At the start of heating (once you press the Holder Button to start);
- When the experience is nearly complete (30 seconds prior the end).
The red light, blinking or steady, on your Holder may indicate that:
- Holder is not charged,
- Device is outside its optimal operating temperature (10°C - 40°C);
- You pressed on the Holder button during usage;
- Holder malfunction.
To resolve the issue, you may try the following:
a. Check that the IQOS 2.4P Pocket Charger is switched ON and has enough power;
b. Place the Holder in the Pocket Charger and wait until it is fully charged (up to 4 minutes);
c. Ensure your Holder’s electric contact is clean;
d. If none of the above works, perform a reset of your device;
e. Still no luck? Please contact IQOS Care by phone - 0800 9900000 or ask for assistance in the nearest IQOS Store.
- Holder is not charged,
- Device is outside its optimal operating temperature (10°C - 40°C);
- You pressed on the Holder button during usage;
- Holder malfunction.
To resolve the issue, you may try the following:
a. Check that the IQOS 2.4P Pocket Charger is switched ON and has enough power;
b. Place the Holder in the Pocket Charger and wait until it is fully charged (up to 4 minutes);
c. Ensure your Holder’s electric contact is clean;
d. If none of the above works, perform a reset of your device;
e. Still no luck? Please contact IQOS Care by phone - 0800 9900000 or ask for assistance in the nearest IQOS Store.
a. Holder light on the IQOS 2.4P Pocket Charger indicates a Holder malfunction. A slowly pulsing red light while charging means that the Holder battery is reaching the end of its life cycle.
b. The bottom light on the Pocket Charger Battery Status indicates a Pocket Charger malfunction or device is outside its optimal operating temperature (10°C - 40°C).
Please, perform a reset of your device and make sure it is in the optimal temperature range.
Still no luck? Please contact IQOS Care by phone - 0800 9900000 or ask for assistance in the nearest IQOS Store.
b. The bottom light on the Pocket Charger Battery Status indicates a Pocket Charger malfunction or device is outside its optimal operating temperature (10°C - 40°C).
Please, perform a reset of your device and make sure it is in the optimal temperature range.
Still no luck? Please contact IQOS Care by phone - 0800 9900000 or ask for assistance in the nearest IQOS Store.
IQOS 2.4P is designed to work in a wide range of temperatures, but the optimal temperature is between 10℃ and 50℃.